Kasco-marine Horizontal Float Manuel d'utilisateur télécharger pdf

Horizontal Float

Assembly & Installation Instructions

A. Circulator (Unit with cord) (1)

B. Float in separate box (1) (Diagram to Right)

1. Float (1)

2. Base Strap (1)

3. Adjustment Bracket (1)

4. Angle Bracket (3)

5. Draw Band (1)

6. U-Bracket (2)

7. Spacer Bracket (2)

8. 1/4” x 1/2” Stainless Steel Bolt (8)

9. 1/4” x 1” Stainless Steel Bolt (3)

10. 1/4” x 1-1/4” Stainless Steel Bolt (2)

11. 1/4” Stainless Steel Lock Nut (8)

12. 1/4” Stainless Steel Hex Nut (2)

13. 1/4” Stainless Steel Lock Washer (5)

14. 50’ Black Nylon Ropes (2)

15. Nylon Tie (1)

PARTS INCLUDED

TOOLS & SUPPLIES NEEDED

• 7/16” Wrench (1)

• 7/16” Socket & Ratchet (1)

• Felt-Tip Marker (1)

STEP ONE

Remove all contents from package and place on a

clean, flat surface. Inspect the shipment for any dam-

ages. If damages are found, immediately notify your

carrier and your Kasco Marine, Inc. representative.

Next, cross reference the parts included in the ship-

ment with the Parts Included sheet in this manual on

page 14. Make sure you have all the parts needed. If

any shortages are found, contact your Kasco repre-

sentative immediately.

STEP TWO

Position the Float upside down (lengthwise channels

facing up) and place the Base Strap so the three holes

in the Base Strap align with the three threaded holes

that comprise the lengthwise midline of the Float.

STEP THREE

Position the Adjustment Bracket over the two holes at

the back end of the Float and Base Strap. Loosely

secure the Adjustment Bracket to the Float using two

1/4” x 1/2” Stainless Steel Bolts and two Stainless

Steel Lock Washers. (See photo above for orienta-

tion.)

STEP FOUR

Place one of the three Angle Brackets perpendicular

to the Base Strap at the front end of the Base Strap.

One of the two center holes of the Angle Bracket

should be positioned over the hole in the Base Strap

and the threaded hole in the Float. Secure the Angle

Bracket to the Float using three 1/4” x 1/2” Stainless

Steel Bolts and three Stainless Steel Lock Washers.

(See photos on the next page for specific instructions

based on the size circulator purchased.) Tighten all

hardware at this time with the 7/16” socket and

wrench.

• Anchors or Stakes for Installation (2)

• 12” pieces of 1” galvanized pipe for weighting

ropes (optional) (2)

1 2 3 4

Résumé du contenu

Page 1 - Horizontal Float

Horizontal Float Assembly & Installation Instructions A. Circulator (Unit with cord) (1) B. Float in separate box (1) (Diagram to Right) 1.

Page 2

STEP FIVE With a felt-tip marker, draw three to four marks around the circumference of the motor housing at the appropriate measurement from the ba

Page 3 - Models 2400, 3400

STEP TEN Attach the Angle Bracket on the motor to the Angle Bracket on the Float using two 1/4” x 1/2” Bolts and two 1/4” Lock Nuts (one

Page 4 - Ice Control Engineering

The Industry Leader in Ice Control Engineering. KASCO MARINE, INC. 800 Deere Road Prescott, WI 54021-1241 Phone (715) 262-4488 * Fax (715) 262-

Commentaires sur ces manuels

Pas de commentaire

Kasco-marine Horizontal Float Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Équipement pour l'eau Kasco-marine Horizontal Float. Kasco Marine Horizontal Float User Manual [en] Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Équipement pour l'eau Kasco-marine Horizontal Float