Kasco-marine J Series Manuel d'utilisateur télécharger pdf (Page 14)

minutes for each tripper on the 24-Hour dial. When

the tripper is pushed to the inside, the switch is in the

“OFF” position.

PROGRAMMING WITH MANUAL OVERRIDE

SWITCH

Your Timer may have a 3-way manual switch or a

2-way manual switch.

AUTOMATIC MODE

In order to operate the time clock in the automatic

mode, the manual switch must be in the automatic

postion- see diagram.

MANUAL MODE

For the 3-way switch, with the manual override switch

in the lower position, marked “O”, the time clock

output will remain Permanently OFF. In the upper

position, marked “I”, the time clock output will remain

permanently ON.

For the 2-way switch, with the manual override switch

in the lower position, marked “ON” the time clock

output will remain permanently ON.

TIME SETTING

TO SET THE CURRENT TIME (AND DAY OF WEEK

ON 7 DAY UNITS), TURN THE MINUTE HAND

CLOCKWISE. DO NOT SET THE TIME BY ROTAT-

ING “OUTER” DIAL.

Turn the minute hand clockwise until the day of the week

(7-day timer) and the time of day on the outer dial is

aligned with the triangle marker on the inner dial (two

o'clock position).

Example for 7-day program dial Monday 10:30 AM. Turn the

minute hand clockwise until Monday 10:30 AM is aligned

with the triangle on the inner dial. The hour and minute hand

will show exactly 10:30.

Example for 24-hour program dial 10:30 AM. Turn the minute

hand clockwise until 10:30 AM is aligned with the triangle on

the inner dial. The hour and the minute dial will show exact-

ly 10:30.

PROGRAMMING

7-Day (SW, QRW Models)

The weekly program dial reflects the seven days of the week

and AM/PM imprints for each day.

The time switch is programmed by pushing the captive trip-

pers to the outer ring position for the entire period that the

load is to be turned “ON”, i.e., two hours for each tripper on

the 7-Day dial. When the tripper is pushed to the inside, the

switch is in the “OFF” position.

24-Hour (ST, QRT Models)

The 24-Hour dial has quarter-hour divisions and AM/PM indi-

cations.

The time switch is programmed by pushing the captive trip-

pers to the outer ring position for the entire period that the

load is to be turned “ON”, i.e., fifteen minutes for each trip-

per on the 24-Hour dial. When the tripper is pushed to the

inside, the switch is in the “OFF” position.

PROGRAMMING WITH MANUAL

OVERRIDE SWITCH

AUTOMATIC MODE

In order to operate the time switch module in the automatic

mode, the manual switch must be in the center position (auto-

matic) - see diagram.

MANUAL MODE

With the manual switch selector lever the selected programs

can be overridden. In the lower position, marked “O”, termi-

nals 3 and 5 are permanently closed. In the upper position,

marked “I”, terminals 3 and 4 are permanently closed (see

diagram).

300GR10020

Override Mode

3-way manual

override switch

I = permanent ON

= automatic

0 = permanent OFF

Dimensions

FM/1 synchronous/quartz

Intermatic Incorporated • Spring Grove, IL 60081 • www.intermatic.com

TIME SETTING

TO SET THE CURRENT TIME (AND DAY OF WEEK

ON 7 DAY UNITS), TURN THE MINUTE HAND

CLOCKWISE. DO NOT SET THE TIME BY ROTAT-

ING “OUTER” DIAL.

Turn the minute hand clockwise until the day of the week

(7-day timer) and the time of day on the outer dial is

aligned with the triangle marker on the inner dial (two

o'clock position).

Example for 7-day program dial Monday 10:30 AM. Turn the

minute hand clockwise until Monday 10:30 AM is aligned

with the triangle on the inner dial. The hour and minute hand

will show exactly 10:30.

Example for 24-hour program dial 10:30 AM. Turn the minute

hand clockwise until 10:30 AM is aligned with the triangle on

the inner dial. The hour and the minute dial will show exact-

ly 10:30.

PROGRAMMING

7-Day (SW, QRW Models)

The weekly program dial reflects the seven days of the week

and AM/PM imprints for each day.

The time switch is programmed by pushing the captive trip-

pers to the outer ring position for the entire period that the

load is to be turned “ON”, i.e., two hours for each tripper on

the 7-Day dial. When the tripper is pushed to the inside, the

switch is in the “OFF” position.

24-Hour (ST, QRT Models)

The 24-Hour dial has quarter-hour divisions and AM/PM indi-

cations.

The time switch is programmed by pushing the captive trip-

pers to the outer ring position for the entire period that the

load is to be turned “ON”, i.e., fifteen minutes for each trip-

per on the 24-Hour dial. When the tripper is pushed to the

inside, the switch is in the “OFF” position.

PROGRAMMING WITH MANUAL

OVERRIDE SWITCH

AUTOMATIC MODE

In order to operate the time switch module in the automatic

mode, the manual switch must be in the center position (auto-

matic) - see diagram.

MANUAL MODE

With the manual switch selector lever the selected programs

can be overridden. In the lower position, marked “O”, termi-

nals 3 and 5 are permanently closed. In the upper position,

marked “I”, terminals 3 and 4 are permanently closed (see

diagram).

300GR10020

Override Mode

3-way manual

override switch

I = permanent ON

= automatic

0 = permanent OFF

Dimensions

FM/1 synchronous/quartz

Intermatic Incorporated • Spring Grove, IL 60081 • www.intermatic.com

AUTO

SETTING THE TIMER

The timer is a 24 hour time clock with 15 minute increment settings.

The captive trippers change the SPDT relay state when pushed

toward the outside.

1. Setting time of day

(a) Synchronize the timer by aligning arrow at the 2:00 position

of inner face with the corresponding time of day printed on the

outer ring.

NOTE: Power must be ON to keep time synchronization.

2. Setting ON time and duration

Locate desired activation time(s) on outer ring (b) and push

trippers to the outside (c). Each tripper represents 15 minutes

activation time. Push as many trippers back as desired for dura-

tion time. When the timer reaches the ﬁ rst tripper, the timer SPDT

contacts will change state and turn ON. It will remain ON for as

long as the following trippers are pushed out. When timer goes

past last tripper, the timer will return to the OFF mode. The timer

has a selector for (d) AUTOMATIC and ON modes.

Overide Mode

2-way manual ON - Permanently ON

overide switch AUTO - automatic

C85 / C95 non-metallic and 3 Phase

Control Panel Timer

TIME CLOCK SETTING

To set the current time, turn the inner dial clockwise.

Do not set the time by rotating “outer” dial.

Turn the minute hand or small plastic inner dial clock-

wise until the time of day on the outer dial is aligned

with the triangle marker on the inner dial (two o’clock

position).

Example for 10:00 AM. Turn the minute hand clock-

wise until 10:00 AM is aligned with the triangle on

the inner dial. The hour and the minute dial will show

exactly 10:00.

Triangle marker

Captive trippers

(in the on position)

PROGRAMMING

The 24-Hour dial has quarter-hour divisions and AM/

PM indications.

The time switch is programmed by pushing the captive

trippers to the outer ring position for the entire pe-

riod that the aerator is to be turned “ON”, i.e., fteen

1 2 ... 9 10 11 12 13 14 15 16 17 18 19 ... 27 28

Commentaires sur ces manuels

Pas de commentaire

Kasco-marine J Series Manuel d'utilisateur Page 14

Commentaires sur ces manuels

Produits connexes et manuels pour Équipement pour l'eau Kasco-marine J Series